440.285.8655
Browne & Co
  • Home
  • About
  • Cutting Tools
    • Carbro
    • CFT - George Whalley
    • Dapra
    • Dummel
    • Everede Tool
    • Fullerton Tool
    • Gaylee Saw
    • Lexington Cutter
    • Nine 9
    • Regal
    • Rockhard
    • Rocky Mountain Twist
  • Accessories
    • ACS - Advanced Chem
    • Alpha Tools
    • Boneham
    • Endurance Carbide
    • Haimer
    • MRO Solutions
    • Precision Brand
    • Safeway Sling
    • Tuffy Products
  • News
  • Contact

Metalcutting Circular Saw Cutting Recommendations, Tips, Tricks & Troublshooting

3/18/2021

6 Comments

 
compiled & edited by Bernard Martin
Martindale Gaylee Carbide HSS Saw Selection troubshooting tips tricks
As more and more of our customers are using Martindale Gaylee Circular saws we put together this guide to the commonly asked questions such as "Is there a rule-of-thumb for the number of teeth?" or "How much side clearance should I have?" Here we cover a lot of the fundamentals of selecting the right circular saw blade configuration, some tips, tricks, and troubleshooting for when things go wrong. 

Circular Saw Feed Rates

These are general cutting speed recommendations for circular saws used in metalcutting from Martindale/Gaylee. The may vary from application to application but are basically some general suggestions starting parameters when using high speed or carbide saws. 
  • HSS Saws: .002”-.006”  (IPT-inch. per tooth / CLPT-chip load per tooth)
  • Carbide Saws: .0002”-.0015”  (IPT -inch. per tooth / CLPT - chip load per tooth)
This is a conservative recommendation as a starting point for feed rates, and may vary depending on material being cut and cutting speed (SFPM).

Selecting the Proper Number of Teeth in Your Metalcutting Saw

Generally speaking, deep cuts and soft material require fewer teeth for chip clearance and stronger teeth (landed) Thin material requires more teeth, but keep-in-mind that at least 2 teeth on the blade need to be engaged in cut.
Saw-TC-Undercutting-Saw
Hard materials and narrow slots (under .025”) likewise require more teeth.

Hard Materials require more teeth, and  give a smoother cut,  but at a much lower production rate.  ​

Alternately beveled teeth keep chips from sticking in the cut and in the tooth gullets.

And Remember that there should be at least 2 teeth engaged in the cut at all times.
Increase Number of Teeth For:
  • Thin material 
  • Thin cuts under .025”
  • Slow spindle speeds
  • Hard material
  • Sand castings 
  • Thin castings 
  • Work hardened materials
  • Known inclusions or Hard spots 

Decrease Number of Teeth For:
  • Free cutting material​
  • Soft Gummy long chipping materials.
  • Deep cuts (over 1/4”)
  • High speeds Machining Applications
  • Chip clearance and tooth strength (Consider Metal Slitting or Copper Slitting style saws.)

Rake Angles and Side Clearance Angles

SIDE CLEARANCE (Tangential Clearance Angle)
This is also known as dish or hollow grind.  You measure down the side of the tip and the difference it is the difference between front and back.  As you cut, material it gets compressed and springs back after the cutting edge passes.

​A steep side clearance angle gives plenty of room for the material to expand and prevents thermal expansion of the base material.  Keep in mint that a very flat side clearance angle can provide a smoother cut in some materials.  For stainless steel and tenacious metals such as copper, zinc, tin or lead an increase in the side clearance is desirable as these materials tend to "spring back" (thermal expansion) on the blade. 

RAKE ANGLES
Rake angle is the term used to describe the direction of the blade’s teeth, as referenced from the rotation and central axis of a saw blade. If you imagine a line going from the exact center of the blade to each tooth, having the front of the tooth directly on that line would be a zero degree rake angle. The rake angle of the blade is described in comparison to that imaginary line.

A positive rake angle meana that the teeth are angled more towards the angle of rotation, while a negative rake angle would mean that they are angled backwards, away from the direction of rotation. Generally speaking, the preferred rake angle is:
  • 5° to 10° positive for other soft materials.
  • 5° negative for yellow brass
  • On center for steel.
Why do Carbide Saws Break?

Why do Circular Saw Blades Break?

It's commonly known that when saw thickness is less than 0.125″, keyways can cause stress risers and cracks.  That is why washers are often used.  However, Breakage, Wobble and Rubbing problems are often caused by how the washers are mounted on either side of saw. 

Remember, washers drive the saw in the absence of a drive key. They must always be clean, flat and bur-free. A speck of dirt will let saws wobble and cut oversize. 

If a saw breaks, it may score the washers. Always check for scoring marks around saw hole for dirt, chips or grit.  Shiny spots, as small as a pinpoint, indicate that chips where imbedded under washers.

Circular skid marks indicate the nut was not tight.

Generally speaking:
  • Thin saws should especially be supported by washers as large as possible.
  • Washers must be of equal diameter or they will flex out saw dish and cause one side of saw to rub.
  • The nut must be wrench-tight.

Saw Blade Teeth most often break as a result of:
  • Too high a feed rate.
  • Spindle bearings are worn.
  • Drive belts  are loose or sheaves worn.
  • Improper tightening: If saw blade pauses momentarily in its rotation while feed advances, it WILL break.
  • Workpiece indexed before the saw has cleared the slot.
  • Improper workholding - The workpiece not tight or not well supported.
  • Saw is dull, even the best tools do eventually wear out.

NOTE: HSS saws will turn colors as they heat during cutting. A straw color is the limit. The saw will lose its temper when it starts turning blue.
6 Comments

    Author

    We've compiled the latest news and technical information about our principals and our market that we hope you find informative!

    Archives

    March 2023
    February 2023
    January 2023
    December 2022
    November 2022
    October 2022
    September 2022
    August 2022
    July 2022
    June 2022
    May 2022
    April 2022
    March 2022
    February 2022
    January 2022
    December 2021
    November 2021
    October 2021
    September 2021
    August 2021
    July 2021
    June 2021
    May 2021
    April 2021
    March 2021
    February 2021
    January 2021
    December 2020
    November 2020
    October 2020
    September 2020
    August 2020
    July 2020
    June 2020
    May 2020
    April 2020
    March 2020
    February 2020
    January 2020
    December 2019
    November 2019
    October 2019
    September 2019
    August 2019
    July 2019
    June 2019
    May 2019
    April 2019
    March 2019
    February 2019
    January 2019
    December 2018
    November 2018
    October 2018
    September 2018
    August 2018
    July 2018
    June 2018
    May 2018
    April 2018
    February 2018
    January 2018
    November 2017
    October 2017
    September 2017
    August 2017
    July 2017
    May 2017
    March 2017
    February 2017
    January 2017
    December 2016
    November 2016
    October 2016
    September 2016
    July 2016
    June 2016
    May 2016
    April 2016
    March 2016
    February 2016
    January 2016
    June 2015
    April 2015
    March 2015
    February 2015
    January 2015
    December 2014
    October 2014
    September 2014
    August 2014
    July 2014
    June 2014
    May 2014
    April 2014
    March 2014
    February 2014
    January 2014
    December 2013
    October 2013
    September 2013
    April 2013
    February 2013
    September 2012
    February 2012
    October 2011
    July 2011
    April 2011
    January 2011
    November 2010
    October 2010
    August 2010
    April 2010
    February 2010
    July 2009
    January 2009
    July 2007

    Categories

    All
    Abrasives
    Advanced Chemical Solutions
    Aerospace
    AirLoc
    Allen Benjamin
    Alpha Tool
    AlumaMill
    Arno Fast Change
    Arno USA
    Asimeto
    Award
    Back Chamfer
    Beveling Base Starter Kit
    Bishop Lifting Products
    Boneham
    Boring
    Boring Bars
    Brian Martin
    Browne & Co.
    Carbide Cutting Tools
    Carbide Drills
    CAT40
    CAT50
    Catalog Download
    Chamfer
    Chip Thinning
    Circular Saws
    Clamping
    Coating
    Coolant
    Coronovirus
    Countersinks
    Custom Tooling
    Cutting Tools
    Dapra
    Dapra Vapor
    Deburring
    Deep Hole Drilling
    Drill Bushing
    Drilling
    Drill Points
    Drills
    Dummel
    Dümmel
    End Mill
    Endurance Carbide
    ER Colllet
    ERGO
    Everede
    Everede Tool
    Fantom
    Feeler Gage
    Flap Wheels
    Forged Wheels
    Fullerton Tool
    Fury
    Gage Reconditioning
    Gaylee Saws
    Gemtex
    George Whalley
    Grooving
    GWS Tool Group
    Haimer USA
    Harmon-i-Cut
    HB Rouse
    HSK
    H Tolerance
    Hydromat
    IBC
    IMTS
    Industrial Supply Assoc
    InovaTool
    Inserts - Boring
    Inserts Grooving
    Inserts - Grooving
    Inserts Milling
    Inserts Parting
    Inserts - Parting
    Inserts- Turning
    Intimidator
    ISA Industrial Supply Assoc
    ISO-9001
    Jergens
    Lexington Cutter
    Live Center
    Lubricants
    Machining Cloud
    Made In USA
    Manufacturing
    Martindale Saws
    Mastercam
    Material: Aluminum
    Material: Bronze
    Material: Cast Iron
    Material: Chromium
    Material: Copper
    Material High Temp
    Material: Inconel
    Material: Steel
    Material: Titanium
    Measuring Tools
    Memorial Day
    Metals
    Metalworking
    Metalworking Fluid
    Metrology
    Mill Turn
    Minimill
    MRO
    Multifunctional Tool
    Nanotech 7000
    NASA
    NATC
    NC Helix Drill
    Nine9
    North American Tool
    Ohio
    Peel Milling
    PMTS
    Polisher
    Precision Brand
    Promotions
    Punches
    QR Code
    Reamers
    Regal
    Rep Of The Year
    RMT Rocky Mountain Twist
    Roll Form Taps
    Rouse Arno
    Rouse - Arno
    Safeway Sling
    Sales
    Sales Tools
    Saw
    Saw Arbors
    Screw Threads
    Shim Stock
    Shrink FIt
    Sling Inspection
    Sling Safety
    Slip Plate
    Sowa
    Spade Drills
    Special Cutting Tools
    Special Tools
    S&R Products
    Stonecutter
    Swiss Machining
    Tap: Carbide
    Tap: Carbide Insert
    Tap Chamfer
    Tap Definitions
    Tap: Extension
    Tap: Metric
    Tapping
    Tap: Pulley
    Taps
    Tap: STI
    Tap: Thread Forming
    Technical Support
    Thread Gaging
    Threading
    ThreadMills
    Thread Tap App
    TIMill
    Tire Mold
    Tool Balancing
    Tool Black
    Toolholders
    Tool Presetter
    Tool Selection
    Tool Wrap
    Trochoidal Milling
    Troubleshooting
    Tuffy Products
    Turning Tools
    Valspar
    Vibration Pads
    Vises
    Weldon Flat
    Workholding

    RSS Feed

Browne & Co., Inc.
9605 Tanager Drive
Chardon, Ohio 44024
Phone 440.285.8655
Fax 440.285.8653
dmb@brownesales.com
© 2023 Browne & Co., Inc. All Rights Reserved
web design by Rapid Production Marketing